Once the wireless settings have been configured, go to the Wireless section, click Use as Access Point. NOTE: If your router does not have this option, do the instructions for Disabling the DHCP Server instead.
Mar 01, 2010 · You can now place the WAP54G Access Point in another nearby location (with its power adapter plugged in) so that it can repeat the wireless signal that it receives from the WRT54G. Notes: The “SSID” of the WAP54G does not have to be the same as the WRT54G. - Set the Cable/DSL Router to (the one you're using as an Access Point) base address to any IP address between 192.168.1.151 to 192.168.1.250 . Second Step: Switch Off the DHCP on the Wireless Cable/DSL Router, and set to Off any filters or special settings that is On if it is used as the main Router. Plug the Wireless Router to the main Router. A second router is connected to WRT54G through ethernet. I have chosen the Buffalo WHR-G125 for the second router because it generally outperforms WRT54G straight out of the box. Fig. 2 WiFi repeater setup with two routers. In this scenario the Linksys still works the same way repeating the distant access point. We are making some network changes here at work. Were getting a second ISP provider and a firewall with dual WAN. So essentially the Firewall is taking the place of the WRT54G2, however, the firewall does not have wireless capability. (costs too much) I was planning on hooking an access The Linksys LAPAC1200C Wireless Access Point is built with Cloud Manager to help greatly streamline network management. Perfect for managing multiple accounts and networks, this browser-based cloud management system allows you to remotely monitor and manage all networks and access points in real time.
Both the Linksys and the Belkin use 192.168.1.1 as the default IP address for each device. I would like to know what settings I need to change i nteh WRT54G to turn it ino an access point -- an extenson of my existing network with teh Belkin router attached to the Comcast modem.
Jan 19, 2009 · Creating a Wireless Access Point using DD-WRT - Refresh 19 January 2009 on DD-WRT, How To, Linksys, Tomato, WRT150N, WRT54G. I found a setup that I like even better than my previous one. I have highlighted the main differences, in red, below. To set it up as repeater do the following: Do a 30 second reset; Under wireless->basic settings The wireless mode list box shown has 3 options - AP, Client, and Ad-hoc. I've been using Client mode, not AP mode. And it clearly says "Client mode: This mode is used when we want the WRT54G to be connected to an AP (Access Point) like a client device (i.e. emulate a PCMCIA card or a PCI card). RE: Use WRT54G as access point SYQUEST (TechnicalUser) 30 Nov 08 22:00 You can configure the WRT54G as a WAP as follows: Log into the WRT54G and change the router IP to the one you want, change the Subnet Mask to the same one your LAN is using, and disable DHCP.
We are making some network changes here at work. Were getting a second ISP provider and a firewall with dual WAN. So essentially the Firewall is taking the place of the WRT54G2, however, the firewall does not have wireless capability. (costs too much) I was planning on hooking an access
Nov 12, 2019 · For all versions of the Linksys WRT54G router, the default password is admin. The WRT54G password is case sensitive. The WRT54G default IP address is 192.168.1.1. It's through this address that you access the router settings and options. There's no default username for the WRT54G, so leave this field blank when logging in. Hey folks, sorry to create another post but I need some help and I didn't know where else to go. Okay so I have my old actiontec GT704-WG router lying around from when I used to have regular high speed internet. I was wondering if I could hook that up in the top floor and be able to have my wifi Use linksys WRT54G v8 as an access point. calvert317 asked on 2009-08-26. Wireless Hardware; Routers; 2 Comments. 2 Solutions. 969 Views. Last Modified: 2013-11-09 Jun 19, 2007 · Save Settings and unhook the network cord from your PC and wrt54g; Now you can connect the incoming lan cable from your main network (or main router) to one of the numbered ports on the wrt54g. This basically turns your wrt54g into a switch or wireless access point. Do not plug anything into the internet port on this second router. Once the wireless settings have been configured, go to the Wireless section, click Use as Access Point. NOTE: If your router does not have this option, do the instructions for Disabling the DHCP Server instead.